EQUIPMENT® for tank systems
Pumps for fuels and engine oils, pump accessories, tank equipment
Double-acting hand vane pump PH-2020-AL
Modern further development of the hand wing pump principle. High-quality materials and state-of-the-art processing guarantee very good performance and a long service life. Four holes (Ø 11mm) in the housing enable good attachment options to machines and systems.
Side blind holes with M8 internal thread are intended for attaching potential equalization cables (EX protection) or vertical brackets. To protect the high-quality pump from contaminated media, a filter screen disc is mounted in the inlet hole of the suction connection.
The pump is suitable for pumping low-viscosity media such as diesel, gasoline, kerosene, alcohols as well as water and water-glycol mixtures. The pump is operated by moving the hand lever mounted on the pump housing back and forth sideways.
A wing system with flap valves sits on the shaft of the hand lever inside the pump. This principle is very robust and effective. It can generate up to 2 bar overpressure. A high-quality counter that can be mounted on the pump housing on the pressure side is available as an accessory.
Centrifugal pump PK-10-010
Recommended for conveying low-viscosity media, e.g. E.g. EL heating oil, diesel, clean water and liquids that do not chemically attack the pump materials.
The pumps are designed so that the medium can be sucked in even if it is mixed with air. Due to their reliability and maintenance-free nature, they are recommended for use in home and building technology and industry, especially for water supply in conjunction with pressure vessels.
- Flow rate up to 80 l/min
- Delivery height up to 70 m, manometric suction height up to 9 m
- Temperature of the pumped medium up to +40 °C
- Ambient temperature up to + 40 °C
- Insulation class: F
- Protection class: IP 44, PK-10-010, three-phase 3x 230/400 V, 50 Hz
Centrifugal pump PK-170-011
Recommended for conveying low-viscosity media, e.g. E.g. EL heating oil, diesel, clean water and liquids that do not chemically attack the pump materials. The pumps are designed so that the medium can be sucked in even if it is mixed with air.
Due to their reliability and maintenance-free nature, they are recommended for use in home and building technology and industry, especially for water supply in conjunction with pressure vessels.
- Flow rate up to 120 l/min
- Delivery height up to 35 m, manometric suction height up to 7 m
- Temperature of the pumped medium up to 90 °C
- Ambient temperature up to 40 °C
- Insulation class: F
- Protection class: IP 44
- PK-170-011: three-phase 3x 230/400 V, 50 Hz
Gerotor pump PG-26
Gerotor pumps are suitable for pumping liquid, lubricating media with a viscosity of 50-500 mm2/s (cSt) and which do not contain any solid impurities or are not prone to solidification.
The design without a coupling saves considerable length. To protect the electric motor from overload, a bypass valve with an opening pressure of 1–10 bar is integrated into the pump (default setting: see table).
Characteristics:
- Robust, compact design, quiet running, self-priming with above-average suction behavior
- high efficiency, easy installation, long service life, SAE flange connection
Gerotor pump PG-60-25
Flow rates from 25 to 60 l/min; Pressures from up to 6 bar; continuous operation
- Temperature range: min. – 10 °C / max. 60 °C
- relative humidity: max. 90%
- quiet operation (less than 70 dB)
- Possible operation with the pressure side closed, thanks to the built-in, adjustable bypass valve (to protect the electric motor from overload)
Attention!
Bypass operation with closed delivery is only permitted for a short time (maximum 2-3 minutes). As soon as the overheating protection is triggered, switch off the power supply and wait until the motor has cooled down. If, in a special application, there is a risk of working in the bypass for a longer period of time, it is absolutely necessary to ensure that the bypassed suction line is not recirculated inside the pump, but is returned to the suction container.
Gear pump PZ-50-122
The gear pump is particularly suitable for pumping media that does not contain any solids, ensures a minimum level of lubricity and is chemically compatible. The standard version is delivered with the direction of rotation “clockwise”.
Simply turning the pump housing by 180° allows you to change the direction of rotation. The direction of flow also changes.
Pump combination Z-PK
The pump combinations Z-PK-2020 (230 V) and Z-PK-2021 (400 V) are used exclusively to pump diesel fuel and EL heating oil. A wide range of applications results from the good delivery rate of up to approx. 40-50 l/min at approx. 5 m delivery height (5 l/min at approx. 35 m height). The ambient temperature of the pump combination is +5 °C to +35 °C. The temperature of the pumped medium is +5 °C to 30 °C. The specified operating temperatures must be adhered to.
The Z-PK pump combinations are a further development of the previous pump combinations. The Z-PK is protected as a utility model. The main feature of this new development is the common pump support to accommodate the electric centrifugal pump and the hand vane pump. No lines or shut-off systems are necessary between the centrifugal pump and the hand vane pump. The Z-PK pump combination is installed inside closed buildings. The pump combination is attached to vertical, load-bearing walls, consoles or other suitable brackets with 4 screws.
Double pump combination Z-PK-EE
The pump combination type Z-PK-2020-EE (230 V; 50 Hz) and ZPK-2021-EE (400 V; 3-phase; 50 Hz), consisting of the well-known pump combination 2x Z-PK-2020 or 2x Z- PK-2021, fully assembled and piped on drip tray. The ZPK-EE pump combinations are used exclusively to pump diesel fuel and EL heating oil.
A wide range of applications results from the good delivery rate of up to approx. 40-50 l/min at approx. 5 m delivery height (5 l/min at approx. 35 m height). The ambient temperature of the pump combination is +5 °C to +35 °C. The temperature of the pumped medium is +5 °C to +30 °C. The specified operating temperatures must be adhered to.
The Z-PK-EE pump combination is installed inside closed buildings. The pump combination is attached to vertical, load-bearing walls, consoles or other suitable brackets with 4 screws.
Oil extraction system OSP
Range:
Decentralized pump station for installation on the engine's oil pan to remove used oil. Used for larger distances between the oil supply system and the combustion engine.
Functionality:
The OSP waste oil extraction unit is used for the central extraction of waste oil from the oil pans of combustion engines. The advantage of the system is the direct positioning of the unit on the engine oil pan. This makes it possible to easily transport waste oil over longer distances to the waste oil tank (no cavitation). The OSP consists of a sheet metal frame to accommodate a waste oil suction pump unit and the decentralized electrical control. An integrated collecting tray protects against contamination in the event of small leakages. The OPS is switched on and off independently of the central control of the IDEAL (MAXIMUM).
Integrated fuses in the pump housing in the form:
a) a level sensor in the pump housing on the suction side of the pump protects against dry running and automatically switches off the OSP when the engine oil pan is drained;
b) When starting up for the first time, button 1 (manual suction) must be kept pressed until the pump body is filled with oil. The control then takes over to switch off the pump. The suction button only bypasses the dry-running protection.
Lubricating oil tank for combination with day tank TTMO-30 / TTMO-60
When large emergency diesel generators run for more than 8 hours, larger amounts of engine lubricating oil are also consumed in addition to diesel fuel. This can result in the lubricating oil level in the engine oil pan falling below the level. We have developed the diesel engine oil day tank combination for this purpose. The basis is Krampitz standard single-walled day tanks with a volume of 500 liters or more. diesel fuel.
We place an additional engine lubricating oil tank with a volume of 30 or 60 liters under this day tank. at. This tank fits the dimensions between the collection tray and the day tank and is located within the external dimensions of the Krampitz standard collection tray. The oil tank is equipped with a content display on the side and a ventilation nozzle.
The flow to the machine is located on the side in the bottom area of the tank. Additional sleeves in the tank roof can accommodate float switches. The diesel fuel day tank can also be equipped with diesel return coolers. The return cooler guarantees that the fuel is cooled down by 20°Celsius. This prevents the fuel in the day tank from heating up to over 50° Celsius.
Level sensor AE-100-E
The flexible level sensor AE-100-E is a float switch for filling levels that works according to the proven reed contact principle. We have been using the high-quality level indicator AE-100-E for over 10 years. It fulfills its task on all continents, whether in extreme heat in Africa or extreme cold in Arctic research stations. There are now over 10.000 AE-100-E in use worldwide.
The level transmitter AE-100-E is generally used for the automatic request or shutdown of pumps when there are reports of specified filling level points (undershoot or overshoot) in tanks. Furthermore, remote signaling or automatic emergency shutdowns are implemented, for example when the filling level falls below the minimum level. The flexible level sensor has a plastic cable with a stainless steel switching head in which a short sliding tube is incorporated. This switching head has such a heavy weight that it cannot float in a liquid and therefore functions like a standpipe.
Krampitz MINOTAUR® tank container
Krampitz BASIS® storage tanks
Krampitz CENTAUR® transport tank and storage tank container
Krampitz EQUIPMENT® for tank systems: